Blog

Blog

NEWS

Company News

Industry News

FAQ

How to select LED light beads? How to select LED light beads?

Currently, the market offers aluminum brackets, brass brackets, and red-copper brackets. Among these, aluminum brackets are the most affordable, while red-copper brackets are the most expensive—often differing in price by more than tenfold. Even among copper brackets, the cost of silver plating varies. On the market, “high-quality brackets” are generally understood to refer to brass brackets that have been silver-plated.

Shenzhen LEDs: How to Identify the Positive and Negative Leads of an LED

Set the multimeter to the R×1K range, and alternately connect the red and black test leads to the two leads of the light-emitting diode. You will observe that, during one of the measurements, the meter needle first deflects to the right by a certain amount and then begins to oscillate slightly around that position, with an amplitude of about one scale division.

How should small LED butterfly light beads be connected for the best effect?

Because small butterfly LED chips have low power and low operating voltage, their use in lighting fixtures typically requires extensive series–parallel connections to meet the required power output. How to properly connect these small butterfly LED chips is a critical issue that demands careful attention; otherwise, the service life of the fixture can be significantly shortened, leading to the awkward situation of “energy savings without cost savings.”

High-power LED indicator lights will see even wider adoption in the lighting industry.

Social development and technological advancement have given rise to a wide array of lighting applications, with high-power LED indicator lights experiencing the most robust growth over the past two to three years.

Why do light-emitting diodes come in different colors?

An LED, or light-emitting diode, is a solid-state semiconductor device that directly converts electrical energy into light. LEDs are made from group III–IV compound semiconductors, such as GaAs (gallium arsenide), GaP (gallium phosphide), and GaAsP (gallium phosphide arsenide), with a PN junction at their core. Consequently, they exhibit the typical I–V characteristics of a P–N junction: forward conduction, reverse cutoff, and breakdown behavior. The heart of an LED is a semiconductor chip, one end of which is mounted on a support substrate; one terminal serves as the negative electrode, while the other is connected to the positive terminal of the power supply, after which the entire chip is encapsulated in epoxy resin.

The light-emitting diode is made from high-quality materials, resulting in higher reliability.

A light-emitting diode is a semiconductor solid-state lighting device that converts electrical energy into light. At its core lies a PN junction. In addition to the typical forward conduction, reverse cutoff, and breakdown characteristics of a PN junction under certain conditions, it also exhibits light-emitting properties. The structure of an LED comprises the following main components: leads, lead frames, encapsulating epoxy, bond wires, the LED chip, solid-state crystal adhesive, and phosphor. Color-changing failures in LED beads are closely related to their materials, structural design, packaging processes, and operating conditions.

What are the applications of light-emitting diodes?

A light-emitting diode, commonly abbreviated as LED, is a type of semiconductor diode made from compounds containing elements such as gallium (Ga), arsenic (As), phosphorus (P), and nitrogen (N), which can convert electrical energy into light energy.

Considerations for Heat Dissipation and Technical Issues of High-Power LED Chips

Appearance and Material: If the finished product does not have stringent sealing requirements and can directly exchange heat with the ambient air, it is recommended to use finned aluminum or copper heat sinks.

Introduction to the Causes of Dead LEDs in the LED Chip Soldering Process

Common soldering methods for LED chips include soldering with a soldering iron, reflow soldering on a heating platform, and wave soldering. Improper soldering techniques can easily lead to dead LEDs. Below, we will specifically discuss the causes of LED chip failure resulting from these common soldering methods.

The Impact of Static Electricity on LED Chip Luminance Failure

It is common to encounter situations where LED chips fail to light up. This issue can arise for packaging companies, application developers, and end users—both organizations and individuals—and is what industry professionals refer to as the “dead LED” phenomenon. There are generally two primary causes: 1) Leakage in the LED chip; excessive current can cause the PN junction to fail, resulting in the LED chip not lighting up. Typically, this condition does not affect the operation of other LEDs in the same assembly.

< 1234567 >